tayco Halifax Скачать руководство пользователя страница 39

Страница: 39 / 55

Seated Height Meeting Table, V-Leg with and without Power

8540-0789

8540-1299

8540-1350

Drill

Robertson # 2

#10 X 1" Pan Head

Screw

Plastic Cover for V-

leg

Cable Clamp, R-

Style

Ensure the install area is

covered for surface

protection.

Lay down the table top

inverted on the working

area.

Install four (4) each V-leg

Assembly aligning to the

pilot holes using #10 x 1”

Pan Head Screws, RB2,

(Figure 1).

Attach the four (4) V-leg

wire grommet cover to V-

leg assembly by inserting

the pin of the wire grommet

cover into the hole of the V-

leg assembly, (Figure 2).

Continued on the next page >>

TABLE TOP W/ GROMMET HOLE
V-LEG ASSEMBLY
PILOT HOLE
#10 X 1” PAN HEAD SCREW, RB2
V-LEG WIRE GROMMET COVER

Figure 1

Figure 2

HOLE

NOTE: Do not pull off the wire

grommet cover. To remove the

wire grommet cover, push

down vertically to dislodge the

pin from the hole.

May 2023

halifax 39

Содержание Halifax
























































Результаты поиска

Содержание Halifax

Отзывы:

Похожие инструкции для Halifax

Бренды по названию

Популярные бренды

tayco Halifax, Руководство по установке

Результаты поиска

Содержание Halifax

Отзывы:

Похожие инструкции для Halifax

Бренды по названию

Популярные бренды