tayco Halifax Скачать руководство пользователя страница 44

Страница: 44 / 55

Gallery Wall and Accent Shelf

Figure 6

Figure 7

Tools & Hardware Needed

8540-0631

8540-0770_Dowel

Drill

Robertson # 2

Tape Measure

3/16” Diam. Drill Bit

1/2” Diam. Drill Bit

Toggle Bolt

Wooden Dowel

Position and align the edges

of the Gallery Wall Backer

Top with the edges of the

Gallery Wall Backer Bottom;

mark the location of Gallery

Wall Backer Top and wall

through holes in the gallery

Wall Backer Top using 3/16”

diam. drill bit, (Figure 6).

Note:

Make sure the side

with the holes for Accent

Shelves are facing up.

Set aside the Gallery Wall

Backer Top.

Steps 4 & 5

10.

Connect the Gallery Wall

Backer Top to Gallery Wall

Backer Bottom by inserting

the Wooden Dowels into the

holes of the Gallery Wall

Backer Top; press the boards

together, (Figure 7).

Continued on the next page >>

GALLERY WALL BACKER BOTTOM
WOODEN DOWEL
GALLERY WALL BACKER TOP

Hole

Hole for Accent Shelf

May 2023

halifax 44

Содержание Halifax
























































Результаты поиска

Содержание Halifax

Отзывы:

Похожие инструкции для Halifax

Бренды по названию

Популярные бренды

tayco Halifax, Руководство по установке

Результаты поиска

Содержание Halifax

Отзывы:

Похожие инструкции для Halifax

Бренды по названию

Популярные бренды