Tatu Marchesan GAT 800 Скачать руководство пользователя страница 67

Страница: 67 / 72

HOISTS - Rev. 07 - Apr/22

9. Maintenance

PROBLEM

CAUSES

POSSIBLE SOLUTIONS

The equipment

does not lift the

load.

Tractor pump is set to less

than 190 bar.

Adjust the pump or change for a more

potent pump.

Pump output rate is low.

Increase the output rate by adjusting

the valve on the tractor.

Weight excess.

Decrease the load to be lifted.

Strange object stopping the

movements.

Check and remove it.

Lack of oil on the tractor.

Check the hydraulic oil on the tractor.

Cylinder is not

moving.

Hoses inverted connected on

the tractor command.

Adjust the hoses.

Hoses are disconnected.

Connect them.

Damaged hoses.

Replace the hoses.

Hydraulic cylinder leaking.

Replace it.

Clogged hose adapters.

Clean them.

Tractor front tilting

up.

Lack of weight on the front.

Add weights.

Troubleshooting guide

- Only

CAPABLE

QUALIFIED

and

AUTHORIZED

personnel must carry out the

maintenance of the equipment.

IMPORTANT

Содержание GAT 800









































































Результаты поиска

Содержание GAT 800

Отзывы:

Похожие инструкции для GAT 800

Бренды по названию

Популярные бренды

Tatu Marchesan GAT 800, Руководство оператора

Результаты поиска

Содержание GAT 800

Отзывы:

Похожие инструкции для GAT 800

Бренды по названию

Популярные бренды