manualshive.com logo in svg

Taski duobot 1850 CE, Руководство пользователя

Поделиться
Скачать
Taski duobot 1850 CE Скачать руководство пользователя страница 22

21

If the system passes the operational 

check, twist the Emergency Stop button 

counterclockwise to reset and press the OK 

button on the user interface.

21.2.  Front Cover Interlock Check

Perform the following steps to verify operation of the front 

cover interlock:

Verifying the front cover interlock requires 

partially opening the front door with the 

machine turned on. Do not open the door 

more than ¼ of the full swing. If the interlock 

fails to operate, personnel may be exposed 

to hazards within the machine.
Verify that the LOG IN screen is shown on 

the user interface. 
Release the two latches on the front cover 

and open the door ¼ of the full swing.

Verify that the system alerts the user with 

three audible beeps and the user interface 

displays the attention symbol and the 

words:

Front door open
Close front door to resume

If the interlock operational check fails, press 

the Emergency Stop button immediately, 

then turn off the system by pressing and 

holding the standby button. Do not use the 

system, it must be repaired by a trained 

service technician.
If the system passes the operational check, 

close the front cover and attach both 

latches, then press the OK button on the 

user interface. 

21.3.  Parking Brake Check

Perform the following steps to verify operation of the 

parking brake:

This procedure requires engaging the drive 

in manual mode. Only use the slowest 

forward speed to verify operation of the 

parking brake. If the parking brake fails, 

using a higher speed reverse direction could 

result in damage to the machine, property, 

or injury to the operator.
Verify that the LOG IN screen is shown on 

the user interface and log into the system 

using your operator code.
Touch the Manual clean button on the home 

screen. 

Touch the forward arrow button once to set 

the slowest speed.

Squeeze the handlebar for one second, 

then release. Verify that the parking brake 

is holding and the machine does not drive 

forward.

Verify the yellow safety light on top of the 

machine flashes while the handlebar is 

pressed.
If the parking brake operational check 

fails, press the Emergency Stop button 

immediately, then turn off the system by 

pressing and holding the standby button. Do 

not use the system, it must be repaired by a 

factory trained service technician.
Turn off the system by pressing and holding 

the standby button. 

21.4.  Touch Shield Check

There are two touch shields. The front touch shield is 

attached to the front cover door. The rear touch shield is 

attached to the main body of the machine. 

1

2

Figure: 42

1 

Front Touch Shield

2 

Rear Touch Shield 

Each touch shield is divided into six zones, front, left front, 

right front, rear, left rear, right rear. Each of the six zones 

must be tested for operation.

Содержание duobot 1850 CE







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды