Task Force Tips TORNADO Скачать руководство пользователя | Manualshive

Страница: 36 / 36

background image

-Press POWER button to turn on electronics.

-Use operator station just like any other wired operator station.

-Press POWER button again to turn off electronics or after 5 minutes of idle operation, handheld unit will automatically

turn off.

If after pressing a button, the OSC & STOW leds alternately flash, this indicates no communication link is present

with the monitor. The handheld unit is out of range or cannot establish a link with the monitor. Move to a different location
and then retry, also verify monitor has power applied.

NOTE!!!

1.2 OPERATION:

1.3 CHANGING BATTERIES:

-Remove two (2) screws on backside of handheld unit and slide bottom half of rubber bumper off enclosure.

-Replace batteries verifying that polarity is correct.

-Replace rubber bumper and retaining screws.

CAUTION

Properly dispose of old batteries. Do not puncture, incinerate, or disassemble batteries.
Do not mix battery types.

2.0 MOUNTING STORAGE BRACKET

Select proper location for mounting storage bracket. Panel spare required will be 6.0“ x 11.2“ (152 x 285mm). Refer
to Figure 2.0 for hole dimensions. Bracket can be used as a template.

Be sure spring is in position.

TASK FORCE TIPS, Inc.

2800 E. Evans Ave, Valparaiso, IN 46383-6940 USA

800-348-2686 • 219-462-6161 • Fax 219-464-7155

MADE IN USA • www.tft.com

Fig 2.0 Wireless Operator Station
Storage Bracket Hole Dimensions

Material

Hole Size

Use

Material

Hole Size

Use

Thickness

Inches

mm

Drill

Thickness Inches

mm

Drill

5/64-3/32

.206

5.2

#5

3/32

.213

5.4

#3

1/8

.213

5.4

#3

1/8

.221

5.6

#2

3/16

.221

5.6

#2

3/16

.228

5.8

#1

ALUMINUM

STEEL

Hole Size Chart For Self Tapping Screws

5"

[127mm]

6"

[152mm]

Drill (3) Pilot Holes
(refer to hole size chart)

Mount Bracket with (3)

1/4-20 Self-Tapping Screws.

Tighten Securely.

Spring

LIY-300 January 24, 2007 Rev02

©Copyright Task Force Tips, Inc. 2005-2007

«
...
34
35
36

Содержание TORNADO





































Отзывы:

Нет отзывов

Похожие инструкции для TORNADO

Бренд: ABB Страницы: 370

Бренд: ABB Страницы: 17

Бренд: ABB Страницы: 104

Бренд: ABB Страницы: 120

Бренд: ABB Страницы: 42

Бренд: Samson Страницы: 100

Бренд: Radio Shack Страницы: 3

Бренд: GBD Страницы: 68

Бренд: Bartlett Страницы: 5

Бренд: Zeagle Страницы: 37

Gemini GEM-P9600

Бренд: NAPCO Страницы: 6

Gemini GEM-P816

Бренд: NAPCO Страницы: 56

Grafica DNE-K07

Бренд: Paradox Страницы: 24

Бренд: Panosol Страницы: 105

Бренд: Pangolin Страницы: 8

Бренд: Watts Страницы: 4

Бренд: Ziton Страницы: 36

Бренд: MaintTech Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды