Task Force Tips TORNADO Скачать руководство пользователя | Manualshive

Страница: 22 / 36

background image

6.2.4.1 PROGRAMMING

- Move monitor to starting point of pattern.

- Press & hold OSC button (~5 seconds) until LED blinks. Release button. LED will continue to blink while in program mode.

- Move monitor to 2nd point, press OSC button. LED will blink rapidly to acknowledge position.

- Repeat until pattern is complete (up to 65 points).

- Press & hold OSC button until LED turns off. Release button.

Figure 6.2.4.1

Operator Station Label

6.2.5 OPERATOR STATION PANELS

The operator stations are all equipped with the same monitor movement functions. From the operator stations, the operator can
command the monitor up, down, left, right and command the nozzle pattern shaper from fog to straight stream. Operator stations
supplied with the membrane switch, shown on the left below, allow the operator to program and perform the oscillate and stow features.

Fig 6.2.5

Operator Station Button Layouts

Read manual before use.

WARNING

®

OSCILLATE PATTERN PROGRAMMING:

1)

2)

3)

4)

5)

Move monitor to starting point of pattern.
Press & hold OSC button until LED blinks. LED will continue to blink in program mode.
Move monitor to 2nd point, press OSC button. LED will blink rapidly to acknowledge position.
Repeat until pattern is complete.
Press & hold OSC button until LED turns off.

NOTE: PATTERN WILL BE CLEARED UPON POWER LOSS.

TO OSCILLATE:

Pattern must be programmed first.)

Press & release OSC button.
(

TO STOW:

Press & release STOW button.
(Programmable, refer to manual.)

Y5705

800-348-2686

www.tft.com/tornado

®

TASK FORCE TIPS

FIRE FIGHTING EQUIPMENT

®

POWER

AUX 2

Read manual before use.

WARNING

800-348-2686

Y5700

www.tft.com

FOG

STRAIGHT

STREAM

AUX 2

HOLD TO

PROGRAM

OSC

HOLD TO

PROGRAM

STOW

AUX 1

22

6.2.4.2 OSCILLATE PATTERN RETAIN FEATURE (DIP #4)

The monitor can be configured so that upon power up, the OSCILLATE
pattern is retained. The OSCILLATE pattern will need be programmed at
least one time (see section 6.2.4.1). To enable the OSCILLATE pattern retain
feature on a monitor follow these steps:

1. Remove lid from monitor operator station.

2. Locate DIP switches on communication board.

3. Slide DIP switch #4 to the ON position.

4. Replace lid. Verify rubber seal is clean and undamaged. Verify that

no wires are caught between lid and box.

5. Program OSCILLATE pattern.

Figure 6.2.4.2

Oscillate Pattern Retain Setup

ON

CTS

12

3

4

«
...
20
21
22
23
24
...
»

Содержание TORNADO





































Отзывы:

Нет отзывов

Похожие инструкции для TORNADO

SolarCell Remote

Бренд: Samsung Страницы: 2

Бренд: B&R Industries Страницы: 89

Бренд: CAME Страницы: 18

Бренд: CAME Страницы: 28

Бренд: CAME Страницы: 28

Бренд: CAME Страницы: 4

Бренд: CAME Страницы: 40

Бренд: CAME Страницы: 26

Бренд: CAME Страницы: 34

Бренд: CAME Страницы: 2

Бренд: Jabra Страницы: 18

IntelliZone2 MasterStat

Бренд: Water Furnace Страницы: 44

Бренд: cinetto Страницы: 56

Бренд: Penn Страницы: 10

iEP-5000G Series

Бренд: ASROCK Страницы: 2

Бренд: Runxin Страницы: 4

Бренд: Water Specialist Страницы: 36

Бренд: GBS Elettronica Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды