Task Force Tips TORNADO Скачать руководство пользователя

Страница: 10 / 36

NOTE: To avoid excessive voltage drop at monitor
operator station, do not lengthen factory supplied power
or monitor cable.

Voltage supplied to PRIMARY OPERATOR STATION should
not fall below 11 volts when monitor is in operation.

Fig 5.0.0 Electrical Components

(standard installation)

Monitor Mounted

Operator Station

Joystick Operator

Station Sec 5.5

13/C-20

Toggle Switch

Operator Station Sec 5.6

Communication

Interface Box Sec 5.7

Tether Operator

Station Sec 5.3

* See Note

Installer Supplied
Power Cable

12 ft (3.7 m) Maximum

- or -

2/C-14, 2/C-20

2/C-14,

2/C-20

2/C-14,

2/C-20

Installer Supplied
Terminal Box

Position Display
(sec 5.8)

- or -

5.0.0 STANDARD WIRING CONFIGURATION

5.0.1 ALTERNATIVE WIRING CONFIGURATION

The electric RC monitor can also be configured with any of the TFT operator stations in figure 5.0.1.

Fig 5.0.1 Electrical Components
(alternative wiring configuration)

NOTE: To avoid excessive voltage drop at monitor
operator station, do not lengthen factory supplied power
or monitor cable.

Voltage supplied to PRIMARY OPERATOR STATION should
not fall below 11 volts when monitor is in operation.

Joystick Operator

Station Sec 5.5

13/C-20

Toggle Switch

Operator Station Sec 5.6

Communication

Interface Box Sec 5.7

Tether Operator

Station Sec 5.3

Installer Supplied Inputs:

Canbus

Toggle Switch

Joystick

Charging Cradle

Wireless Operator

Station Sec 5.4

Receiver

Deutsch

Connector

9/C-20

Monitor Mounted

Operator Station

2/C-14, 2/C-20

12 ft (3.7 m) Maximum

Position Display
(sec 5.8)

- or -

Optional Operator

Station Sec 5.2

2/C-14

10 ft (3 m) Maximum

Primary Operator

Station Sec 5.1

** See Note

Power

30 or 100 ft
(9 or 27 m)

- or -

- or - - or - - or -

2/C-14,

2/C-20

Содержание TORNADO





































Результаты поиска

Содержание TORNADO

Отзывы:

Похожие инструкции для TORNADO

Бренды по названию

Популярные бренды

Task Force Tips TORNADO, Инструкции по установке, безопасной эксплуатации и обслуживанию

Результаты поиска

Содержание TORNADO

Отзывы:

Похожие инструкции для TORNADO

Бренды по названию

Популярные бренды