Task Force Tips TORNADO Скачать руководство пользователя | Manualshive

Страница: 32 / 36

background image

Addendum

RC Monitor Installation Manuals

LIY-200, LIY-300, LIX-300

TASK FORCE TIPS, Inc.

2800 E. Evans Ave, Valparaiso, IN 46383-6940 USA

800-348-2686 • 219-462-6161 • Fax 219-464-7155

MADE IN USA • www.tft.com

®

YE-REMAUX Remote Auxiliary Interface Box

The Remote Auxiliary Interface Box allows a user to utilize the AUX1 and AUX2 buttons located on the monitor operator
station or any remote operator station. The Interface Box is equipped with two relays that can operate lights, interface to a
valve controller or in some cases operate a valve directly, etc. The contact rating of the relay is 16 amps @ 30VDC for
resistive loads and 8 amps @ 30VDC for inductive loads.

The installer will need to mount the interface box and connect the cable to power and the communication link of the
monitor.

1.0 ENCLOSURE MOUNTING

Select proper enclosure location. Enclosure is designed to be surface mounted and the size is 5” x 3 1/8” (127 x 80mm).
Height of enclosure is 2 3/8” (60mm). Refer to Figure 1.0.1 for mounting hole dimensions.

Figure 1.0.1

Hole Dimensions

1.1 ELECTRICAL WIRING

The interface box needs to be connected to +12/24VDC (red) and ground (black). The blue & white wires from the
interface box cable need to be connected to the blue & white wires from the monitor. A terminal box or a high quality,
protected splice can be used to make these connections. See section 5.0 of installation manuals for further wiring
information.

Each relay has one Form-C contact (common, normally open, normally closed) that can be used.

MOUNT ENCLOSURE

WITH (2) 1/4-20 FASTENERS

TIGHTEN SECURELY.

4.45

2.05

The Interface Box provides no overload protection for the device it is controlling. Failure
to provide overload protection will damage relay contacts, which will disable device
being controlled.

WARNING

©Copyright Task Force Tips, Inc. 2006

LIY-ADD1 April 26, 2006 Rev00

«
...
30
31
32
33
34
...
»

Содержание TORNADO





































Отзывы:

Нет отзывов

Похожие инструкции для TORNADO

615 Series ANSI

Бренд: ABB Страницы: 60

Бренд: Garmin Страницы: 220

Бренд: Gardena Страницы: 16

coviva Smartbox TKP100A

Бренд: hager Страницы: 4

Бренд: Vag Страницы: 12

iBox Hub 25020180

Бренд: Hans Grohe Страницы: 36

Бренд: Walimex Pro Страницы: 68

Бренд: Raypak Страницы: 24

Бренд: J+J Страницы: 91

Бренд: Absima Страницы: 5

Бренд: Desoutter Страницы: 74

Бренд: jablotron Страницы: 2

Бренд: Samson Страницы: 70

Бренд: Keysight Technologies Страницы: 105

Бренд: Phoenix Contact Страницы: 56

Бренд: Yoshitake Страницы: 21

Бренд: Oasis Страницы: 7

Бренд: FMS Страницы: 108

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды