Task Force Tips TORNADO Скачать руководство пользователя | Manualshive

Страница: 19 / 36

background image

19

5.10.2.1 LADDER INSTALLATION ELECTRICAL WIRING

The electronics enclosure converts discrete input signals into serial communications for controlling
the monitor. The discrete input signals can be from a joystick, toggle switches, relay contacts or
Canbus output module. The electronic interface a12/24 VDC signals, but can be field
changed to accept ground signals.

The electronics enclosure is configured so that signals connected to the PRIMARY CONTROL cable
will override any other operator stations (see section 6.2.1).

See Figure 5.10.2.1 for wiring connections.

Figure 5.10.2.1

Electrical Components

(ladder installations)

Recommended

Cable Gauge

Max Length

Gauge

40 ft. . . . . . . 14AWG
65 ft. . . . . . . 12AWG
80 ft . . . . . . 2-14AWG

105 ft . . . . . . 10AWG
130 ft . . . . . 2-12AWG

NOTE: To avoid excessive voltage drop at monitor
operator station, cable selection is critical.

Voltage supplied to ELECTRONICS ENCLOSURE should
not fall below 11 volts when monitor is in operation.

5.10.2.2 PLATFORM INSTALLATION ELECTRICAL WIRING

The electronics enclosure converts discrete input signals into serial communications for controlling
the monitor. The discrete input signals can be from a joystick, toggle switches, relay contacts or
Canbus output module. The electronic interface a12/24 VDC signals, but can be field
changed to accept ground signals.

The electronics enclosure is configured so that signals connected to the PRIMARY CONTROL cable
will override any other operator stations (see section 6.2.1).

See Figure 5.10.2.2 for wiring connections.

Figure 5.10.2.2

Electrical Components

(platform installations)

NOTE: To avoid excessive voltage drop at monitor
operator station, cable selection is critical.

Voltage supplied to ELECTRONICS ENCLOSURE
should not fall below 11 volts when monitor is in
operation.

Recommended

Cable Gauge

Max Length

Gauge

40 ft. . . . . . . 14AWG
65 ft. . . . . . . 12AWG
80 ft . . . . . . 2-14AWG

105 ft . . . . . . 10AWG
130 ft . . . . . 2-12AWG

5.11 ELECTRIC NOZZLE ACTUATOR WIRING

The electric Tornado RC monitor is designed to control and is factory wired for a TFT electric actuated nozzle. Task Force Tips nozzles
are available with a male cord plug. After mounting the appropriate nozzle onto the monitor, plug the male cord from the nozzle into the
female cord located on the outlet of the monitor. Make sure the two coupling nuts are tightened securely to ensure a proper watertight
seal.

If retrofitting an existing TFT nozzle, a male cord plug (TFT #Y5285) can be purchased and installed in place of the existing actuator
cord. Please consult factory for installation.

«
...
17
18
19
20
21
...
»

Содержание TORNADO





































Отзывы:

Нет отзывов

Похожие инструкции для TORNADO

SolarCell Remote

Бренд: Samsung Страницы: 2

Бренд: Parker Страницы: 42

Бренд: Vag Страницы: 12

LOWARA Aquavara IPC

Бренд: Xylem Страницы: 292

Бренд: Yolink Страницы: 23

ZoneSense Plus AS

Бренд: Halma Страницы: 58

Бренд: FASAR ELETTRONICA Страницы: 2

Бренд: ACS Страницы: 2

Бренд: Litex Страницы: 1

Бренд: Scanreco Страницы: 48

Бренд: Eaton Страницы: 2

Бренд: Audioplex Страницы: 1

BLEUBOX R-IN-UHF-5239U

Бренд: iDTRONIC Страницы: 13

Бренд: Konig Страницы: 8

CIMR-VC*****H**-00 series

Бренд: YASKAWA Страницы: 32

Бренд: Stramatel Страницы: 10

Бренд: Srne Страницы: 13

Бренд: HomeMatic Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды