Tartan 4000 Скачать руководство пользователя страница 44

T4000 OM 

 

   

and    treated    once    or    twice    a    year    with    an   interior   teak   oil.   

   

12.3.2   Cherry   

   

Interior    cherry    surfaces    have    a    high    solids    conversion    varnish    finish.          This    should   
be    regularly    washed    off    with    fresh    water    and    a    little    liquid    detergent,    then   
polished    with    a    chamois    leather.   Please    consult    with    the    factory    before    refinishing   
varnished   cherry   surfaces.   

   

   

12.4                  Bottom   of   the   Yacht

   

   

   Note:      Following   this   factory   approved   method   will   not   void   your   hull   blister   warranty.   

   

   

Although   we   use   the   finest   gelcoats   available   today,   our   testing   indicates   that   sanding   
these   gelcoats   seriously   degrades   blister   resistance.       By   following   the   approved   finishing   
methods   you   will   maintain   your   hull   blister   warranty   protection   as   well   as   protect   your   
investment   for   years   to   come.   

   

BOTTOM   PAINTING   BARE   FIBERGLASS

   

   

1.   Scrub   the   surface   thoroughly   with   soap   and   water   using   a   stiff   brush.   Flush   with   fresh   
water   to   remove   soap   residue.   

   

2.   Wipe   surface   thoroughly   with   a   rag   that   has   been   dampened   with   Interlux   Fiberglass   
Solvent   Wash   202   or   an   equivalent   de-­‐waxing   agent   to   remove   mold   release   agents,   wax   
and   other   contamination.    Wipe   off   with   a   clean   dry   rag   before   liquid   dries.   Wipe   only   a   few   
square   feet   at   a   time   and   change   rags   frequently.   

   

3.   Lightly   spray   the   surface   with   water   to   insure   all   contamination    has   been   removed.   If   
water   beads   up   or   separates   repeat   Step   2.   

   

4.   Lightly   sand   all   gelcoated   areas   with   a   3M   Medium   Scotch-­‐Brite   Hand   Pad   or   320   grit   
sandpaper.   Lightly   sand   gray   Interprotected    areas   with   a   320   grit   sandpaper   until   blended   
into   surrounding   areas   to   achieve   a   smooth   finish   if   desired.      Be   careful   not   to   sand   into   the   
gelcoat.      Sand   the   keel   and   rudder   with   a   220   grit   sandpaper   to   achieve   a   smooth   finish   if   
desired.   

   

AFTER   THE   SURFACE   HAS   BEEN   PROPERLY    PREPARED

   

   

1.         Remove   the   sanding   residue   by   wiping   with   Fiberglass   Solvent   Wash   202.   

   

2.      Apply   antifouling   paint   following   manufacturers    recommended    application   
procedures.      A   sandless   primer   such   a   Pettit   6999   may   be   recommended    for   certain   
bottom   paints.   

Содержание 4000

















































































Отзывы: