Tartan 4000 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 80

Tartan 4000 Скачать руководство пользователя страница 43

T4000 OM

appearance.

The galley and head sinks are fiberglass and can be maintained with the same
care as other gelcoat surfaces.

Gelcoat   surfaces   will   stain   if    the   yacht   is   moored   where   leaves   fall   on   deck   or   birds
roost.     Under   these   conditions,     surfaces   should   be   scrubbed     down   very   frequently.
A   protective     cover   may   offer protection and reduce maintenance.

12.1.2PPG Paints:

PPG   Paints   should   be   cleaned   with   warm   water   and   a   mild   detergent.        Lights   scuffs
in   the   PPG    finish   can   be   buffed   out   using   a light   compound   such   as   3M   Finesse   It   II
Polish.     Contact PPG for   care and maintenance   guidelines on   your PPG hull.       Touch up
kits are available through an   authorized PPG Dealer.

PPG DCC CONCEPT

Acrylic Urethane

PPG Technical Assistance

1-‐800-‐647-‐6050

12.2 Portlights and Hatches

The portlights and hatches of your yacht are manufactured by various companies.

The   portlights     are   stainless       trimmed     with   safety     glass   or   Lexan.          Screen     inserts
are   included.          Lexan,     which     is   impact-‐ resistant   and   very   durable   is   used   in   the
hatches   as   well   as   the   companionway   sliding   hatch.       However,   the   surface   of   the
Lexan   is   not   abrasion   resistant,   and   therefore,   gritty   cleaning   agents   should   never
be   used   on   them.            Clean        Lexan        with   mild   soap   and   water.        If   Lexan        requires
polishing,     Lexan     polish     is   available   from   most   major   hardware   dealers.        Toothpaste
may   be   used   as   a   substitute   for   Lexan   polish.   Rinse   afterward   with   mild   soap   and
water.        Please   consult   the   hatch   and   portlight   manufacturers   for   care    and
maintenance guidelines.

12.3

Wood

12.3.1 Teak

Interior   teak   surfaces   are   maintained   in   the   following   manner:            Remove   dirt   or
cooking   grease   from   teak   surfaces   before   refinishing.   This   can   be   done   by   washing
down   the   surface   with   mild   soap   and   water.          Interior   surfaces   should   be   cleaned

«
...
41
42
43
44
45
...
»

Содержание 4000

















































































Отзывы:

Нет отзывов