Tally Dascom DL-820 Скачать руководство пользователя страница 12

Страница: 12 / 82

Tally Dascom DL-820

User Guide V1.0

............................................................................................

...........................................................................................................................................................

6.2 Ethernet

....................................................................................................................................................

6.3 Parallel

......................................................................................................................................................

6.4 Serial

.........................................................................................................................................................

6.5 Wifi

.............................................................................................................................................................

CHAPTER 7 OPTION INTRODUCTION

.......................................................................................................

7.1 Using the cutter

.......................................................................................................................................

7.2 Using the peeler

......................................................................................................................................

CHAPTER 8 CODE PAGES

...........................................................................................................................

8.1 ASCII character set

.................................................................................................................................

8.2 CP 437 USA

.............................................................................................................................................

8.3 CP 850

......................................................................................................................................................

8.4 CP 860 Portuguese

................................................................................................................................

8.5 CP 863 French

........................................................................................................................................

8.6 CP 865 Nordic

.........................................................................................................................................

8.7 CP 858 European

....................................................................................................................................

8.8 CP 866 Cyrillic

.........................................................................................................................................

8.9 CP 852 Latin

............................................................................................................................................

CHAPTER 9 COMMAND CODES

.................................................................................................................

9.1 ZPL Command Set

.................................................................................................................................

9.2 EPL Command Set

.................................................................................................................................

Содержание DL-820



















































































Результаты поиска

Содержание DL-820

Отзывы:

Похожие инструкции для DL-820

Бренды по названию

Популярные бренды

Tally Dascom DL-820, Руководство пользователя

Результаты поиска

Содержание DL-820

Отзывы:

Похожие инструкции для DL-820

Бренды по названию

Популярные бренды