Takeuchi TB285 Скачать руководство пользователя страница 80

Страница: 80 / 274

2-32

CONTROLS

blade lever

leverS and pedalS

Use this lever to operate the dozer blade.

(A) .......Blade up

(B) ......Blade down

Refer to “Operating the dozer blade” on

page 3-15.

Machines with the float switch (USA

specification)

Warning

• Do not press the float button while the

machine is raised by the blade. Doing

so will cause the machine to fall. If you

must work beneath the raised machine,

always use a secure support to keep the

machine raised.

• Do not press the float button while the

blade is raised. Doing so will cause the

blade to fall. Lower the blade to the

ground before pressing the float button.

• Do not travel forward while the blade is

in the float mode.

Float operation

Button (C) . Float mode

Press the float switch to set the

dozer blade to the float mode.

To cancel the float mode, press

the switch again.

Содержание TB285



















































































































































































































































































Результаты поиска

Содержание TB285

Отзывы:

Бренды по названию

Популярные бренды

Takeuchi TB285, Руководство оператора

Результаты поиска

Содержание TB285

Отзывы:

Бренды по названию

Популярные бренды