Takeuchi TB285 Скачать руководство пользователя страница 187

Страница: 187 / 274

5-51

MAINTENANCE

replacing the air breather filter

Warning

Oil may spurt out if caps or filters are

removed or pipes are disconnected

before releasing the pressure in the

hydraulic system.

• Press the air breather button to relieve

the tank pressure.

every 1000 hourS

1. Open the side cover.

2. Press the button (N) to relieve the internal

pressure from the tank.

3. Loosen the nut and remove the button (N)

on the air breather.

4. Remove the cover (H).

5. Replace the filter (A).

6. Install the cover (H) on the body (B).

7. Install the button (N).

inSpecting and adJuSting the

engine valve clearance

This operation requires experience. Ask your

sales or service dealer for it.

retightening the engine cylinder

head bolt <tb285>

This operation requires experience. Ask your

sales or service dealer for it.

inSpecting the engine

compreSSion preSSure <tb290>

This operation requires experience. Ask your

sales or service dealer for it.

inSpecting and cleaning the

engine Starter and the alternator

<tb290>

This operation requires experience. Ask your

sales or service dealer for it.

Содержание TB285



















































































































































































































































































Результаты поиска

Содержание TB285

Отзывы:

Бренды по названию

Популярные бренды

Takeuchi TB285, Руководство оператора

Результаты поиска

Содержание TB285

Отзывы:

Бренды по названию

Популярные бренды