Takeuchi TB285 Скачать руководство пользователя страница 163

Страница: 163 / 274

5-27

MAINTENANCE

Adjustment

<TB285>

If the belt tension is not normal, adjust it with

the adjuster bolt (2).

1. Loosen the locking nut (3).

2. Turn the adjuster bolt (2) as follows.

· Tighten: Clockwise

· Loosen: Counterclockwise

3. Tighten the locking nut (3) after

adjustment.

Tightening torque:

· Locking nut (4) 31.4 to 45.1 N·m (23.2

to 33.3 ft-lb.)

<TB290>

If the belt tension is not normal, tilt the

compressor to adjust the tension.

1. Loosen the fixing bolt (5) and fixing nut (6).

2. Turn the adjuster bolt (7) as follows.

· Tighten: Clockwise

· Loosen: Counterclockwise

3. Tighten the fixing bolt (5) and fixing nut (6)

upon completion of adjustment.

Note:

When replacing with a new belt, run

the engine at low idle speed for about 3 to 5

minutes to break in the new belt, before

adjusting the tension again.

Replacing

Replace the belt in the following cases:

· There are cuts or cracks.

· The belt is worn and touches the bottom of

the V groove in the pulley.

· The belt stretched too loose to be

adjusted.

after the initial 50 hourS (only for new machineS)

Содержание TB285



















































































































































































































































































Результаты поиска

Содержание TB285

Отзывы:

Бренды по названию

Популярные бренды

Takeuchi TB285, Руководство оператора

Результаты поиска

Содержание TB285

Отзывы:

Бренды по названию

Популярные бренды