Takeuchi TB285 Скачать руководство пользователя страница 68

Страница: 68 / 274

2-20

CONTROLS

mainTenance mode display

While in the data mode, press and hold the

DATA (2) side for three seconds to enter the

maintenance mode.The display changes

each time the DATA (2) side is pressed as

follows:

1. Vehicle error code

inStrument cluSter

IMPORTANT: If an error code appears,

immediately stop the operation and

contact your sales or service dealer for

help.

Displays two three or four-digit error codes,

with the latest code in the left.

Refer to “Vehicle error code list” on page

6-12.

2. Engine error code

IMPORTANT: If an error code appears,

immediately stop the operation and

contact your sales or service dealer for

help.

Displays three error codes, with the latest

code at the top.

Refer to “Engine error code list” on page

6-14.

3. Auxiliary 1st-2 setting information

The electric current value in the solenoid

that controls the auxiliary flow rate is

displayed.

The flow rate, except the flow rate of the

auxiliary 1st-1, can be changed when the

engine is at rest and the starter switch is

set to ON.

The actual flow rate is not in conjunction

with the value expressed in percent.

For setting the auxiliary piping flow rate,

ask your service or sales dealer.

Changing flow rate

a. Raise the safety lock lever to the lock

position.

b. Press and hold the auxiliary flow rate

select switch for approximately three

seconds to cause the values displayed

on the L side to flash.

c. Pressing the TRIP side of the Trip/Data

switch decreases the flow rate by 5%.

Pressing and holding it for one second

decreases the flow rate by 5%.

Pressing the DATA side of the Trip/Data

switch increases the flow rate by 5%.

Pressing and holding it for one second

increases the flow rate by 5%.

Initial

condition

Variable

range

Auxiliary 1st-1 100%

100%

—

Auxiliary 1st-2

75%

10 to

100%

Auxiliary 1st-3

50%

10 to

100%

Auxiliary 2nd

100%

10 to

100%

Auxiliary 4th

100%

10 to

100%

The table shows the electric current values.

d. Press the auxiliary flow rate select

switch to confirm. At this time, the

values on the R side start flashing.

Perform the same operation as for the L

side. The section to be set changes

each time the auxiliary flow rate select

switch is pressed.

Содержание TB285



















































































































































































































































































Результаты поиска

Содержание TB285

Отзывы:

Бренды по названию

Популярные бренды

Takeuchi TB285, Руководство оператора

Результаты поиска

Содержание TB285

Отзывы:

Бренды по названию

Популярные бренды