Takeuchi TB285 Скачать руководство пользователя страница 262

Страница: 262 / 274

8-6

OPTIONS

hydraulic breaker

For handling of the breaker, read the

hydraulic breaker’s manual, provided

separately.

IMPORTANT: When installing an

attachment, make sure that it is

appropriate for the machine being used.

Contact your sales or service dealer for

advice on selecting attachments.

cautionS on operating

hydraulic breaker

• Start the engine and run it at 75% of the

maximum speed.

• Pound with the chisel pressed

perpendicular to the surface to be

pounded.

• When pounding, press the chisel properly

against the object to be broken so as to

avoid pounding the air.

• Do not pry with the chisel or do not pry

while pounding.

• Do not move the chisel while pounding.

• Do not pound continuously for over 30

seconds on the same surface.

• Do not pound with the cylinder fully

extended or retracted (at the stroke end).

Leave a margin of at least 50mm(2 in).

• Do not pound with the arm placed

perpendicular to the ground surface.

Содержание TB285



















































































































































































































































































Результаты поиска

Содержание TB285

Отзывы:

Бренды по названию

Популярные бренды

Takeuchi TB285, Руководство оператора

Результаты поиска

Содержание TB285

Отзывы:

Бренды по названию

Популярные бренды