Takenaka System FC2200GE Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 58

Takenaka System FC2200GE Скачать руководство пользователя страница 6

M10510B;6/58

- 6 -

Camera fixing screw hole
(bottom)

When using this equipment on a place
subject to constant vibration or impact, it is
recommended to employ a screw lock type
LAN cable.
Firmly screw a locking screw into a connector
fixing screw hole when using a screw lock
type cable.
Insert the LAN connector with the retaining
latch facing upward until it clicks both for
Screw lock type and Universal type..

(3-4) Display LED

Three indicator LEDs are laid on the rear panel

・

Operation indicator LED (POW: Three colors: green/red/orange)
It lights up (or brinks ) to indicate that the camera is powered.
When the camera is set in the asynchronous shutter mode, It lights up in red for one shot in response to the input of the
external trigger signal.

・

Link speed indicator LED (SPD: orange)
It lights up in orange to indicate that the camera is connected to LAN port (LAN card) or HUB of Gigabit Ethernet
Interface (1000BASE-T).
It turns off when the camera is connected to LAN port (LANBASE-T, 10BASE-T) of which communication speed is lower than
1000BASE-T or when the camera is connected to nothing.

・

Link status indicator LED (LINK: green)
It lights up when the camera is connected to the other LAN port via Ethernet and the data-access is running as well.

Name

Color

OFF

ON

Blinking

SPD

Orange

Disconnected from LAN
or Connecting at 10Mbps/100Mbps

Connecting at 1000Mbps

-

LINK

Green

Disconnected from LAN

Connected to LAN

Data accessing

(3-5) How to fix the Camera

The camera is fixed using four screw holes on the bottom or each two screw holes on the top
and side.
Use  an  available  tripod  attachment  (AT500)  to  fix  the  camera  with  a  screw  for  a  tripod
(1/4-20UNC).

(!) This equipment is not shipped with a tripod attachment .

(Note) The tripod attachment (AT500) can be attached only on the bottom surface.
(Note) Pay attention to thread length of the fixing screw.(See 15. External dimensions)

There is a possibility that excessively long screw may cause damage to internal structure.

(3-6) Connection when using a power cable for pin number conversion

The pin arrangement of the power connector when using 6pin -12 pin conversion cable (6P12G-XX) is shown in the following
table.
[Pin arrangement of the power cable for pin number conversion cable (6P12G-XX)]
6 pin (Camera side) – pin number

12 pin (Power supply side) – pin number

Signal name

Contents

1

1

GND (0V)

Power ground

2

-

NC

No connection

3

5,12

GND

Signal ground

4

6

Vint

Input for external trigger

5

11

STRB

Strobe timing signal

6

2

+12VDC

DC power Input

-

3,4,7,8,9,10

NC

No connection

* It is able to directly connect to TAKENAKA’s camera power unit (PU100) by using this cable.

→

See (4-1) Connection method

(Note) The option cable is separately needed when auto iris lens is connected.

Universal LAN cable

Screw lock type LAN cable

«
...
4
5
6
7
8
...
»

Содержание FC2200GE



























































Отзывы:

Нет отзывов