Takenaka System FC2200GE Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 58

Takenaka System FC2200GE Скачать руководство пользователя страница 5

M10510B;5/58

- 5 -

3. Description of Each Component

(3-1) Description of rear panel of camera

The following parts are laid on the rear panel as shown on
the right diagram..

・

Camera connector

・

LAN connector

・

Connector fixing screw

・

Operation indicator LED

・

Link speed indicator LED

・

Link status indicator LED

(!) Rotary switch and toggle switch which are equipped on the

conventional FC series camera are not equipped.
The  camera  operation  setting  (parameter  setup)  is  performed
using  serial  communication  function  of  application  software  via
LAN connection.

(3-2) Camera connector (HRS HR10A-7R-6PB)

The pin arrangement of the camera connector (6 pins) and the
signals assigned to those pins are shown in the following table:

１

２

３

４

５

６

（

Pin arrangement viewed from

the outside of the camera

）

Pin No.

Signal name

Description

I/O

1

GND (0V)

Power ground

2

IRIS *1

Image signal for Auto iris lens

Out

3

GND

Signal ground

4

Vint

Input for external trigger

In

5

STRB *2

Strobe timing signal

Out

6

+12VDC

DC power Input

(In)

*1

・・・

”IRIS” is the false image signal output exclusively used for controlling the image signal input type-Auto iris lens

It is not possible to take out the normal image signal from this pin terminal.
*2

・・・

Strobe signal(STRB) and Busy signal(BUSY) can be output from this terminal. Default setting for those are OFF and H

level signal is normally output. When it is required to output any of those signals, it is necessary to set the configuration
register via serial communication or to change setting of Digital IO-LineSource d of GenICam API to any of
(Strobe,Busy).

(3-3) LAN connector (Standard type RJ-45 connector)

This is the LAN connector (RJ-45 type) conforming to Gigabit Ethernet interface (1000BASE-T/IEEE802.3ab).
It is connected with the LAN connector of PC using standard LAN cable conforming to Gigabit Ethernet.

[Pin arrangement of LAN connector (RJ-45)]

8 7 6 5 4 3 2 1

Pin arrangement of

RJ-

45

connector

Pin No.

Signal name

Description

I/O

1

TP0+

Twisted pair 0 (+)

In/Out

2

TP0-

Twisted pair 0 (-)

In/Out

3

TP1+

Twisted pair 1 (+)

In/Out

4

TP2+

Twisted pair 2 (+)

In/Out

5

TP2-

Twisted pair 2 (-)

In/Out

6

TP1-

Twisted pair 1 (-)

In/Out

7

TP3+

Twisted pair 3 (+)

In/Out

8

TP3-

Twisted pair 3 (-)

In/Out

Camera connector

Operation indicator LED

LAN connector

Link speed indicator LED

Link status indicator LED

Connector fixing screw

«
...
3
4
5
6
7
...
»

Содержание FC2200GE



























































Отзывы:

Нет отзывов