Takenaka System FC2200GE Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 58

Takenaka System FC2200GE Скачать руководство пользователя страница 16

M10510B;16/58

- 16 -

(5-2) Setting of shutter speed

The shutter speed is determined by assigning “0 - 9” to the shutter switch position or specifying the shutter speed in H
(Horizontal scan time) unit.
As this camera is not equipped with the substantive shutter setting switch, the shutter speed is specified by changing the
Feature settings regarding the exposure time of GenICam API or using the serial communication command via serial
communication software.

The shutter speed setting is mainly decided by setting position “0” to ”9” of (Hypothetical) shutter switch.

●

Correspondence relation between Shutter speed and shutter switch setting

Table 5-2 Setting value of shutter speed

Shutter speed

Position of
shutter switch

High speed shutter

(continuous/asynchronous)

Low speed shutter

(continuous)

0

No shutter (continuous) 1/5 second (2056H=1V)

1

1/8600 second

(1H)

1/2.50 second

(2V)

2

1/3000 second

( 3H)

1/1.67second

(3V)

3

1/1200 second

(8H)

1/1.25 second

(4V)

4

1/600 second

(17H)

1/1.00 second

(5V)

5

1/240 second

(43H)

1/0.83second

(6V)

6

1/120 second

(86H)

1/0.71 second

(7V)

7

1/60 second

(171H)

1/0.63 second

(8V)

8

1/30 second

(343H)

1/0.56 second

(9V)

9

1/15 second (686H)

Pulse width control
/asynchronous (!)

1/0.50 second

(10V)

(Note)  (H) and (V) in the table represent the horizontal time unit and the vertical time (frame duration) unit respectively.
(Note)  ”No shutter” in the table means the continuous shutter mode with exposure time = 1 frame duration.
(Note)  The  value  of  the  each  shutter  speed  is  the  factory  default  value.  The  shutter  speed  of  each  position  (excluding

shutter position = 0) is possible to change by the user with serial communication command.

(!) As for this camera, “Pulse width control time/asynchronous” must be set to be “Pulse width control (PWC) =

ENABLED”.
When it is set to be “Pulse width control (PWC) = DISABLED” (default), the selection can be made out of the 9 levels
not only for the continuous shutter operation but also for the asynchronous shutter operation.

(!)

“Shutter switch” means the hypothetical shutter switch set on the memory inside the camera via serial communication
command.

[Explanation]
The shutter speed is specified by reading out the value on the electronic shutter table (separately exist on page A to F )
corresponding to the set position of shutter switch.(excluding directly designated value )
The electronic shutter table can all be rewritten with the serial command “E” (shutter table Edit command) except shutter switch ”0”..

«
...
14
15
16
17
18
...
»

Содержание FC2200GE



























































Отзывы:

Нет отзывов