TAG MIL-BOOK 100 Series Скачать руководство пользователя

Страница: 29 / 131

Getting Started

1-14

Taking a Look at the Docking Station (option)

This section identifies the external components of the docking station
and briefly describes the function of each component.

Right-Side Components

Ref

Component

Description

See Also

Device

Indicators

Shows the current status of the docking station
and computer’s devices.

AC Power Indicator – glows green when
computer is connected to AC power.

Docking Station Connection Indicator:
– glows green when the computer is properly
connected to the docking station.
– glows orange when the computer is not
connected properly to the docking station.

•

Release Tab

Press the Release Tab on both sides and lift up
to release computer from docking station.

Audio Output
Connector

Connects a Hi-Fi set, radio set, synthesizer,
walkman, etc.

•

Microphone

Connector

Connects an external microphone.

Содержание MIL-BOOK 100 Series




































































































































Результаты поиска

Содержание MIL-BOOK 100 Series

Отзывы:

Похожие инструкции для MIL-BOOK 100 Series

Бренды по названию

Популярные бренды

TAG MIL-BOOK 100 Series, Руководство оператора

Результаты поиска

Содержание MIL-BOOK 100 Series

Отзывы:

Похожие инструкции для MIL-BOOK 100 Series

Бренды по названию

Популярные бренды