TAG MIL-BOOK 100 Series Скачать руководство пользователя

Страница: 21 / 131

Getting Started

1-6

Ref

Component

Description

See Also

Battery Charge Indicator:
– glows green when the battery is fully
charged.
– Glows orange when the battery is being
charged.
– Is dark when battery has no charge left
and AC adapter is connected and
powered on.

System State Indicator:
– glows green when the computer is
powered on.
– Glows orange when the computer is in
Suspend mode.

AC Power Indicator – glows green when
computer is connected to AC power and is
powered-on.

•

PC Card Slot

Accepts a PC Card for additional
functions.

RJ-45 Connector

Connects the LAN cable.

•

RJ-11 Connector

Connects the telephone line.

•

USB Port

Connects an USB device such as printer,
digital camera, joystick and more.

Содержание MIL-BOOK 100 Series




































































































































Результаты поиска

Содержание MIL-BOOK 100 Series

Отзывы:

Похожие инструкции для MIL-BOOK 100 Series

Бренды по названию

Популярные бренды

TAG MIL-BOOK 100 Series, Руководство оператора

Результаты поиска

Содержание MIL-BOOK 100 Series

Отзывы:

Похожие инструкции для MIL-BOOK 100 Series

Бренды по названию

Популярные бренды