background image

 Troubleshooting

8-4

Battery Problems

The battery does not charge (Battery Charge LED indicator does

not light orange).

l

 Make sure that the AC adapter is properly connected.

l

 Make sure that the battery is not too hot – gets above 55

o

C

  or too cold – below 0

o

C. Allow time for the battery pack to

  return to room temperature.

l

 Make sure that the battery pack is installed correctly.

l

 Make sure that the battery terminals are clean.

The operating time of a fully charged battery becomes shorter.

l

 If you often partially recharge and discharge, the battery might not be

  charged to its full potential. Initialize the battery to solve the problem.
  (See “Initializing the Battery Pack” in Chapter 3 for instructions.)

l

 Make sure that power to the computer is off. If you use the computer

  during recharging for more than 4 hours, the recharging will stop no
  matter whether the battery has been fully charged or not. If this
  happens, you can disconnect and then reconnect the AC adapter to
  start the recharging again.

The battery operating time indicated by the battery meter does not

match the actual operating time.

l

 The actual operating time can be different from the estimated time,

  depending on how you are using the computer. If the actual operating
  time is much less than the estimated time, initialize the battery. (See
  “Initializing the Battery Pack” in Chapter 3 for instructions.)

Содержание MIL-BOOK 100 Series




































































































































Отзывы: