TAG MIL-BOOK 100 Series Скачать руководство пользователя

Страница: 124 / 131

Troubleshooting

8-11

WARNING:

COM3 is reserved for use by the touchscreen, do not disable it. If COM1/2 is

disabled and COM3/4 is enabled on the SCU Setup (refer to chapter 5), upon

booting system would recognize the enabled COM3/4 and designate it as COM1/2.

The following table is the default settings:

COM Port

I/O (input/output) Port

IRQ (Interrupt Request)

COM1 (available)

3F8

IRQ4

COM4 (reserved for
Wireless Modem)

2E8

IRQ5

COM3 (reserved for
touchscreen only)

3E8

IRQ3

The PC Card stops communicating properly.

The application may have been reset when the computer is turned off

or in Standby mode. Exit and restart the application.

Power Management Problems (for Windows)

The computer does not enter Standby or Suspend mode

automatically.

If you have a connection to another computer, the computer does not

enter Standby or Suspend mode if the connection is actively in use.

Make sure that the Standby or Suspend time-out is enabled.

The computer does not enter Standby or Suspend mode immediately.

If the computer is performing an operation, it normally waits for the

operation to finish.

The computer does not resume from Standby or Suspend mode.

The computer automatically enters Standby or Suspend mode when the
battery pack is empty. Does any one of the following:

−

Connect the AC or car adapter to the computer.

−

Replace the empty battery pack with a fully charged one.

Содержание MIL-BOOK 100 Series




































































































































Результаты поиска

Содержание MIL-BOOK 100 Series

Отзывы:

Похожие инструкции для MIL-BOOK 100 Series

Бренды по названию

Популярные бренды

TAG MIL-BOOK 100 Series, Руководство оператора

Результаты поиска

Содержание MIL-BOOK 100 Series

Отзывы:

Похожие инструкции для MIL-BOOK 100 Series

Бренды по названию

Популярные бренды