manualshive.com logo in svg

Suzuki DF150AP, Руководство пользователя

Поделиться
Скачать
Suzuki DF150AP Скачать руководство пользователя страница 90

90

NOTE:
Before applying grease through the steering
bracket grease nipple, lock the motor in the fully
tilted up position.

Clutch lever

Marine-grade 
water resistant 
grease
(Grease Gun)

Swivel bracket

Steering bracket

Engine holder

Use a hand operated grease gun and follow the
steps below when servicing the grease nipple

A

 on the engine holder.

1. Turn the engine off and allow it to cool.
2. Inject approximately 10 grams of grease at

initial 20 hours.
Inject approximately 5 grams of grease at
every 100 hours (12 months).

NOTE:
If grease will not inject into the fitting, consult
your Authorized Suzuki Marine Dealer.

Your authorized Suzuki Marine Dealer may also
have additional recommendations due to
regional climate or operating conditions.
Please consult him for advice.

NOTICE

Using a hydraulic or air powered grease
gun to service the grease nipple 

A

 on the

engine holder may cause damage to the
oil seal. 

Do not use powered grease guns when
servicing grease nipple 

A

 on the engine

holder.

Содержание DF150AP












































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды