manualshive.com logo in svg

Suzuki DF150AP, Руководство пользователя

Поделиться
Скачать
Suzuki DF150AP Скачать руководство пользователя страница 27

27

2. If the boat tends to veer to port, move the

rear end of the trim tab toward the port side.
If the boat tends to veer to starboard, move
the rear end of the trim tab toward the star-
board side.

3. Tighten the bolt that holds the trim tab in

place.

After adjusting the trim tab, check to see if the
boat still tends to veer to one side. If necessary,
readjust the trim tab.

CONTROL HANDLE ADJUSTMENT

The control handle friction and control handle
detent force can be adjusted to suit operator’s
preference. The control handle friction adjust-
ment will change the overall effort to move the
control handle. This will help prevent undesired
movement of the control handle in rough water
conditions. Consult your authorized Suzuki
marine dealer to adjust the control handle fric-
tion and detent force.

IDLE SPEED ADJUSTMENT

The idle speed has been factory adjusted
between 600 – 700 r/min. in neutral.

NOTE:
If idle speed cannot be set within the specified
range, contact your authorized Suzuki Marine
Dealer.

Type

Adjustable item

A

Friction and detent force

B

Friction

Type A

72

&0

Type B

Содержание DF150AP












































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды