manualshive.com logo in svg

Suzuki DF150AP, Руководство пользователя

Поделиться
Скачать
Suzuki DF150AP Скачать руководство пользователя страница 89

89

8. Drain the fuel and water in the filter cup into

a suitable container.

9. Pull out the filter element 

6

. Inspect the filter

element 

6

, O-ring 

7

 and seal ring 

8

 for

damage. If they are damaged, replace them.

10. Wash the filter element with clean solvent

and dry it.

11. Reinstall the seal ring and filter element in

their original positions.

12. Verify that the O-ring is in place in the top of

the filter cup and screw the filter cup back
into place.

13. Connect the water sensor lead wire connec-

tor 

3

.

14. Reinstall the resonator by securing the

bolts.

15. Restart the engine and check that there are

no leaks around the fuel filter.

NOTE:
If any water exists in the fuel filter cup, remove
the cup and drain the water. Always dispose of
excess fuel safely. For questions, consult your
authorized Suzuki marine dealer.

NOTICE

If spilled gasoline is just left on painted
surface, it may cause a stain or discolora-
tion of the surface coating.

Wipe off any spilled gasoline immediately
with a soft cloth etc.

LUBRICATION

Proper lubrication is important for the safe,
smooth operation and long life of each working
part of your outboard motor. The following chart
shows the lubrication points of your motor and
the recommended lubricant:

LOCATION

LUBRICANT

Shift link

Marine-grade 
water resistant 
grease

Propeller shaft

Trim ram pad

Содержание DF150AP












































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды