manualshive.com logo in svg

Suzuki DF150AP, Руководство пользователя

Поделиться
Скачать
Suzuki DF150AP Скачать руководство пользователя страница 30

30

1. Engine Speed Display Screen

The engine speed 

1

, shift position 

2

, trim

position 

3

, time 

4

, engine position 

5

 and

sub information 

6

 are displayed.

The sub information display can be switched
by pressing the [

] or [

] buttons.

This screen can be selected between digital
and analog display. (Refer to the MENU
INFORMATION SELECTION section)

2. Speed/Fuel Information Display Screen

The speed 

1

, fuel level 

2

, sub information

3

 and time 

4

 are displayed.

The sub information display can be switched
by pressing the [

] or [

] buttons.

This screen can be selected between digital
and analog display. (Refer to the MENU
INFORMATION SELECTION section)

Digital

Analog

Digital

Analog

3. Fuel Information Display Screen

This screen indicates the remaining fuel lev-
els of each tank installed, along with sub
information.
The sub information display can be switched
by pressing the [

] or [

] buttons.

This screen indicates only in digital mode.

No.3
No.4

No.1
No.2

Содержание DF150AP












































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды