manualshive.com logo in svg

Suzuki DF150AP, Руководство пользователя

Поделиться
Скачать
Suzuki DF150AP Скачать руководство пользователя страница 45

45

The “Check Shift control” indication clears when
any of the button is pressed in the gauge. How-
ever, the caution alarm icon is displayed until
eliminating the cause.

GAUGE COMMUNICATION CAUTION 
SYSTEM

This system activates when there is a commu-
nication error of the gauge.

If this system activates, the “Check Gauge C.” is
indicated on the screen.

The “Check Gauge C.” indication clears when
any of the buttons are pressed on the gauge. 

NOTICE

If this system activates for no apparent
reason, there may be a problem with the
system.

Consult your authorized Suzuki marine
dealer. 

NOTICE

If this system activates for no apparent
reason, there may be a problem with the
system.

Consult your authorized Suzuki marine
dealer.

STATION SETTING TROLL MODE 
CAUTION SYSTEM

This system is activated when the TROLL mode
operation is started on the gauge screen of the
cockpit, where the TROLL Mode operation is
not available.

If this system activates, the “Check Station Set-
ting” is displayed on screen.

Identify the cockpit where the SELECT LED on
the control panel is turned ON and perform the
TROLL Mode operation from the gauge screen
of that cockpit where the SELECT LED is
turned ON.

On the gauge screen where the TROLL Mode
operation is available, 

 is displayed.

The “Check Station Setting” indication clears
when any of the button is pressed in the gauge.

Содержание DF150AP












































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды