manualshive.com logo in svg

Suzuki DF150AP, Руководство пользователя

Поделиться
Скачать
Suzuki DF150AP Скачать руководство пользователя страница 51

51

If this system activates, stop the engine imme-
diately, if wind and water conditions are safe to
do so, and check the fuel filter/water  separator
for water. Or consult your authorized Suzuki
marine dealer.

For inspection and cleaning of the fuel filter,
refer to the LOW PRESSURE FUEL FILTER in
the INSPECTION AND MAINTENANCE sec-
tion.

OPERATION OF TILTING 
SYSTEMS

POWER TRIM AND TILT

The “Power Trim and Tilt” is operated by press-
ing the switch. To tilt the motor up, press the
upper part of the switch. To tilt the motor down,
press the lower part of the switch.

If equipped with Keyless Start System:

 WARNING

The power trim and tilt (PTT) switch on
the side cover can be accidentally acti-
vated when the Keyless Start System is in
OFF state, resulting in injury. 

Keep all persons away from the outboard
motor to help prevent accidental activa-
tion of the PTT system. 

UP

DOWN

DOWN

UP

Содержание DF150AP












































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды