manualshive.com logo in svg

Suzuki DF150AP, Руководство пользователя

Поделиться
Скачать
Suzuki DF150AP Скачать руководство пользователя страница 12

12

NOTE:
If equipped with Keyless Start System:
Turn the Keyless Start System to OFF state
before connecting or disconnecting the rotation
select connector.

If not equipped with Keyless Start System:
Turn the main switch OFF before connecting or
disconnecting the rotation select connector.

Regular select connector

Counter select connector

BATTERY INSTALLATION

BATTERY REQUIREMENT

850 Marine Cranking Amps (MCA)/ABYC,
or 670 Cold Cranking Amps (CCA)/SAE
or 180 Reserve Capacity (RC) Minutes/SAE

NOTE:
• The specifications listed above are the mini-

mum battery rating requirements for starting
the engine. 

• If your boat application requires additional

battery loads, it is recommended that an aux-
iliary battery or batteries be installed. Consult
your Suzuki dealer for proper battery installa-
tion information. 

• Dual-purpose (Cranking/Deep-cycle) batter-

ies can be used if they meet the minimum
specifications listed above (MCA, CCA, or
RC).

• Do not use a Deep Cycle battery for the main

cranking battery.

• When connecting batteries in parallel, they

must be of the same type, capacity, manufac-
turer, and of similar age. When replacement
is necessary, they should be replaced as a
set. Consult your Suzuki dealer for proper
battery installation information.

Содержание DF150AP












































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды