Supero SuperServer 6027PR-HC1FR Скачать руководство пользователя страница 128

Страница: 128 / 138

7-32

SUPERSERVER 6027PR-HC1(R/TR/FR) USER'S MANUAL

Station IP Address

This item displays the Station IP address for this computer. This should be in decimal
and in dotted quad form (i.e., 192.168.10.253).

Subnet Mask

This item displays the sub-network that this computer belongs to. The value of each
three-digit number separated by dots should not exceed 255.

Station MAC Address

This item displays the Station MAC address for this computer. Mac addresses are
6 two-digit hexadecimal numbers.

Gateway IP Address

This item displays the Gateway IP address for this computer. This should be in
decimal and in dotted quad form (i.e., 192.168.10.253).

7-5 Boot

This submenu allows the user to configure the following boot settings for the

system.

Содержание SuperServer 6027PR-HC1FR











































































































































Результаты поиска

Содержание SuperServer 6027PR-HC1FR

Отзывы:

Похожие инструкции для SuperServer 6027PR-HC1FR

Бренды по названию

Популярные бренды

Supero SuperServer 6027PR-HC1FR, Руководство пользователя

Результаты поиска

Содержание SuperServer 6027PR-HC1FR

Отзывы:

Похожие инструкции для SuperServer 6027PR-HC1FR

Бренды по названию

Популярные бренды