Supero SuperServer 6027PR-HC1FR Скачать руководство пользователя страница 102

Страница: 102 / 138

7-6

SUPERSERVER 6027PR-HC1(R/TR/FR) USER'S MANUAL



CPU Configuration

This submenu displays the following information of the CPU as detected by the

BIOS. It also allows the user to configure CPU settings.



Socket 1 CPU Information, Socket 2 CPU Information

This submenu displays the following information regarding the CPUs installed in
Socket 1 and Socket 2.

•

Type of CPU

•

CPU Signature

•

Microcode Patch

•

CPU Stepping

•

Maximum CPU Speed

•

Minimum CPU Speed

•

Processor Cores

•

Intel HT (Hyper-Threading) Technology

•

Intel VT-x Technology

•

Intel SMX Technology

•

L1 Data Cache

•

L1 Code Cache

•

L2 Cache

•

L3 Cache

CPU Speed

This item displays the speed of the CPU installed in Socket 1 or Socket 2.

64-bit

This item indicates if the CPU installed in Socket 1 or Socket 2 supports the 64-bit

technology.

Clock Spread Spectrum

Select Enable to enable Clock Spectrum support, which will allow the BIOS to
monitor and attempt to reduce the level of Electromagnetic Interference caused by
the components whenever needed. The options are

Disabled

and Enabled.

RTID (Record Types IDs)

This feature displays the total number of Record Type IDs for local and remote
pools. The options are

Optimal

and Alternate.

Содержание SuperServer 6027PR-HC1FR











































































































































Результаты поиска

Содержание SuperServer 6027PR-HC1FR

Отзывы:

Похожие инструкции для SuperServer 6027PR-HC1FR

Бренды по названию

Популярные бренды

Supero SuperServer 6027PR-HC1FR, Руководство пользователя

Результаты поиска

Содержание SuperServer 6027PR-HC1FR

Отзывы:

Похожие инструкции для SuperServer 6027PR-HC1FR

Бренды по названию

Популярные бренды