Supermicro X5DE8-GG Скачать руководство пользователя страница 7

Страница: 7 / 90

Chapter 1: Introduction

1-1

Introduction

Chapter 1

Introduction

1-1

Overview

Checklist

Congratulations on purchasing your computer motherboard from an ac-

knowledged leader in the industry. Supermicro boards are designed with

the utmost attention to detail to provide you with the highest standards in

quality and performance.

Please check that the following items have been included with your mother-

board. If anything listed here is damaged or missing, contact your retailer.

One (1) Supermicro Mainboard

One (1) ribbon cable for IDE devices

One (1) floppy ribbon cable

One (1) USB cable

One (1) COM port (serial) cable

One (1) I/O backpanel shield

One (1) Supermicro CD or diskettes containing drivers and utilities

One (1) User's/BIOS Manual

Two (2) Pentium 4 Xeon active heatsinks (FAN-042, retail only)

Two (2) heatsink retention clip kits (SKT-095-604)

SCSI Accessories (X5DE8-GG only)

One (1) 68-pin LVD Ultra320/160 SCSI cable

One (1) set of SCSI driver diskettes

One (1) SCSI manual

Содержание X5DE8-GG



























































































Результаты поиска

Содержание X5DE8-GG

Отзывы:

Похожие инструкции для X5DE8-GG

Бренды по названию

Популярные бренды

Supermicro X5DE8-GG, Руководство пользователя

Результаты поиска

Содержание X5DE8-GG

Отзывы:

Похожие инструкции для X5DE8-GG

Бренды по названию

Популярные бренды