Supermicro X5DE8-GG Скачать руководство пользователя страница 40

Страница: 40 / 90

2-16

SUPER X5DE8-GG/X5DEI-GG/X5DEE-M User's Manual

SCSI Enable/Disable
(X5DE8-GG)

The SCSI Termination jumper at

JPA3 allows you to enable or dis-

able the onboard SCSI controller.

The normal (default) position is on

pins 1-2 to enable (terminate) the

onboard SCSI. See the table on

the right for jumper settings.

Jumper

Position

Pins 1-2
Pins 2-3

Definition

Enabled

Disabled

SCSI Enable/Disable

Jumper Settings

(JPA3)

LAN1/2 Enable/Disable

Change the setting of jumper JPL1

(for LAN1) or JPL2 (for LAN2) to

enable or disable the Ethernet

ports on the motherboard. See the

table on the right for jumper set-

tings. The default setting is en-

abled.

Note:

the X5DEE-M has a single

LAN port and thus a single jumper.

Jumper

Position

Pins 1-2
Pins 2-3

Definition

Enabled

Disabled

LAN1/2

Enable/Disable

Jumper Settings

(JPL1, JPL2)

SCSI Channel Termination
Enable/Disable (X5DE8-GG)

Jumpers JPA1 and JPA2 allow you to

enable or disable termination for each

SCSI channel. Jumper JPA1 controls

channel A and JPA2 controls channel

B. The default setting is open to en-

able (teminate) both SCSI channels.

If you wish to connect external SCSI

devices, you should disable termina-

tion for the channel(s) you will be con-

necting them to. Note that the exter-

n a l S C S I p o r t i s f o r u s e w i t h

rackmount chassis only. See the

table on the right for jumper settings.

Jumper

Position

Open

Closed

Definition

Enabled

Disabled

SCSI Channel T ermination

Enable/Disable

Jumper Settings

(JPA1, JPA2)

Содержание X5DE8-GG



























































































Результаты поиска

Содержание X5DE8-GG

Отзывы:

Похожие инструкции для X5DE8-GG

Бренды по названию

Популярные бренды

Supermicro X5DE8-GG, Руководство пользователя

Результаты поиска

Содержание X5DE8-GG

Отзывы:

Похожие инструкции для X5DE8-GG

Бренды по названию

Популярные бренды