Supermicro X5DE8-GG Скачать руководство пользователя страница 22

Страница: 22 / 90

1-16

Introduction

SUPER X5DE8-GG/X5DEI-GG/X5DEE-M User's Manual

Microsoft OnNow

The OnNow design initiative is a comprehensive, system-wide approach to

system and device power control. OnNow is a term for a PC that is always

on but appears to be off and responds immediately to user or other re-

quests.

Slow Blinking LED for Suspend-State Indicator

When the CPU goes into a suspend state, the chassis power LED will start

blinking to indicate that the CPU is in suspend mode. When the user presses

any key, the CPU will wake-up and the LED will automatically stop blinking

and remain on.

Main Switch Override Mechanism

When an ATX power supply is used, the power button can function as a

system suspend button to make the system enter a SoftOff state. The

monitor will be suspended and the hard drive will spin down. Depressing

the power button again will cause the whole system to wake-up. During

the SoftOff state, the ATX power supply provides power to keep the re-

quired circuitry in the system alive. In case the system malfunctions and

you want to turn off the power, just depress and hold the power button for

4 seconds. This option can be set in the Power section of the BIOS Setup

routine.

External Modem Ring-On

Wake-up events can be triggered by a device such as the external modem

ringing when the system is in the SoftOff state. Note that external modem

ring-on can only be used with an ATX 2.01 (or above) compliant power

supply.

Wake-On-LAN (WOL)

Wake-On-LAN is defined as the ability of a management application to re-

motely power up a computer that is powered off. Remote PC setup, up-

dates and asset tracking can occur after hours and on weekends so that

daily LAN traffic is kept to a minimum and users are not interrupted. The

motherboards have a 3-pin header (WOL) to connect to the 3-pin header on

Содержание X5DE8-GG



























































































Результаты поиска

Содержание X5DE8-GG

Отзывы:

Похожие инструкции для X5DE8-GG

Бренды по названию

Популярные бренды

Supermicro X5DE8-GG, Руководство пользователя

Результаты поиска

Содержание X5DE8-GG

Отзывы:

Похожие инструкции для X5DE8-GG

Бренды по названию

Популярные бренды