Supermicro X5DE8-GG Скачать руководство пользователя страница 24

Страница: 24 / 90

1-18

Introduction

SUPER X5DE8-GG/X5DEI-GG/X5DEE-M User's Manual

(UARTs), one of which supports serial infrared communication. Each UART

includes a 16-byte send/receive FIFO, a programmable baud rate generator,

complete modem control capability and a processor interrupt system. Both

UARTs provide legacy speed with baud rate of up to 115.2 Kbps as well as

an advanced speed with baud rates of 250 K, 500 K, or 1 Mb/s, which

support higher speed modems.

The Super I/O supports one PC-compatible printer port (SPP), Bi-directional

Printer Port (BPP) , Enhanced Parallel Port (EPP) or Extended Capabilities

Port (ECP).

The Super I/O provides functions that comply with ACPI (Advanced Con-

figuration and Power Interface), which includes support of legacy and ACPI

power management through an SMI or SCI function pin. It also features

auto power management to reduce power consumption.

The IRQs, DMAs and I/O space resources of the Super I/O can flexibly

adjust to meet ISA PnP requirements, which suppport ACPI and APM (Ad-

vanced Power Management).

Содержание X5DE8-GG



























































































Результаты поиска

Содержание X5DE8-GG

Отзывы:

Похожие инструкции для X5DE8-GG

Бренды по названию

Популярные бренды

Supermicro X5DE8-GG, Руководство пользователя

Результаты поиска

Содержание X5DE8-GG

Отзывы:

Похожие инструкции для X5DE8-GG

Бренды по названию

Популярные бренды