Supermicro X5DE8-GG Скачать руководство пользователя страница 66

Страница: 66 / 90

4-14

UPER X5DE8-GG/X5DEI-GG/X5DEE-M

User’s Manual

Peripheral Device Configuration

Power Lost Control

This option determines how the system will respond when power is reap-

plied after a power loss condition. Choose

Last State

to automatically

start up the system when power is reapplied after an AC power loss.

Always Off means you must push the main power button to restart the

system after power is restored.

System Health Monitor

The BIOS continuously monitors the health of your system by measuring

certain voltage levels and temperatures.

CPU1 Current Temperature
CPU2 Current Temperature
System Current Temperature

These readings display the real-time temperatures of CPU1, CPU2 and the

system. There are also several voltage level monitors as shown on the

System Health Monitor screen.

CPU Overheat Support

This option allows you to specify the action taken when an overheat

situation occurs. The settings are

Shutdown

and Slowdown.

System Overheat Warning

This option allows you to enable or disable the system overheat warning.

The settings are

Enabled

and Disabled. (See Overheat Warning Temp.)

Remote Access Configuration

Remote Access

This option allows the user to redirect the console (display) through the

COM port when enabled. This is useful when two computers are hooked

up to a single monitor. The function keys are disabled when this setting is

enabled. The settings are "Serial ANSI" and "

Disabled

Содержание X5DE8-GG



























































































Результаты поиска

Содержание X5DE8-GG

Отзывы:

Похожие инструкции для X5DE8-GG

Бренды по названию

Популярные бренды

Supermicro X5DE8-GG, Руководство пользователя

Результаты поиска

Содержание X5DE8-GG

Отзывы:

Похожие инструкции для X5DE8-GG

Бренды по названию

Популярные бренды