Supermicro X5DE8-GG Скачать руководство пользователя страница 42

Страница: 42 / 90

2-18

SUPER X5DE8-GG/X5DEI-GG/X5DEE-M User's Manual

2-9

Parallel Port, Floppy/Hard Disk Drive and SCSI

Connections

Note the following when connecting the floppy and hard disk drive cables:

•

The floppy disk drive cable has seven twisted wires.

•

A red mark on a wire typically designates the location of pin 1.

•

A single floppy disk drive ribbon cable has 34 wires and two connectors to

provide for two floppy disk drives. The connector with twisted wires always

connects to drive A, and the connector that does not have twisted wires

always connects to drive B.

Parallel (Printer) Port
Connector

The parallel (printer) port is lo-

cated on J9. See the table on the

right for pin definitions.

Pin Number

Function

Strobe-

Data Bit 0

Data Bit 1

Data Bit 2

Data Bit 3

Data Bit 4

Data Bit 5

Data Bit 6

Data Bit 7

ACK

BUSY

SLCT

Pin Number

Function

Auto Feed-

Error-

Init-

SLCT IN-

G ND

Parallel (Printer) Port Pin Definitio ns

(J9)

Содержание X5DE8-GG



























































































Результаты поиска

Содержание X5DE8-GG

Отзывы:

Похожие инструкции для X5DE8-GG

Бренды по названию

Популярные бренды

Supermicro X5DE8-GG, Руководство пользователя

Результаты поиска

Содержание X5DE8-GG

Отзывы:

Похожие инструкции для X5DE8-GG

Бренды по названию

Популярные бренды