manualshive.com logo in svg

Supermicro SuperStorage SSG-136R-NR32JBF, Руководство пользователя


Поделиться
Скачать
background image

27

SuperStorage SSG-136R-NR32JBF User's Manual

3.3 Chassis Components

Ruler Drives

Your system likely came with drives installed. The SSG-136R-NR32JBF supports 32 hot-
swappable RSSDs (Ruler SSDs). Drives are installed and removed by extending a ruler from 
the chassis.
Note that NVMe RSSDs must be prepared prior to removal from the system, as detailed below.

Warning:

 Surprise hot removal of an RSSD can result in loss of all data on the drive. The 

following instructions must be followed for safe removal of RSSDs.

How to Safely Remove Ruler SSDs

Linux Environment

Examples listed here were done under RHEL 7.4. Command output in this section may be 
abbreviated for easier reading.

1. Begin by retrieving the SSD information, as shown below.

# lsblk
NAME          MAJ:MIN RM  SIZE RO TYPE MOUNTPOINT
sda             8:0    0 59.6G  0 disk

├─sda1          8:1    0    1G  0 part /boot
└─sda2          8:2    0 58.6G  0 part
  ├─rhel-root 253:0    0   50G  0 lvm  /
  └─rhel-swap 253:1    0    6G  0 lvm  [SWAP]

nvme10n1      259:10   0  3.7T  0 disk
nvme11n1      259:12   0  3.7T  0 disk
nvme12n1      259:11   0  3.7T  0 disk
nvme13n1      259:19   0  3.7T  0 disk
nvme14n1      259:18   0  3.7T  0 disk
nvme15n1      259:14   0  3.7T  0 disk
nvme16n1      259:13   0  3.7T  0 disk
nvme17n1      259:15   0  3.7T  0 disk
nvme18n1      259:17   0  3.7T  0 disk
nvme19n1      259:20   0  3.7T  0 disk
nvme20n1      259:16   0  3.7T  0 disk
nvme21n1      259:24   0  3.7T  0 disk

Содержание SuperStorage SSG-136R-NR32JBF












































































Отзывы:

Нет отзывов

Похожие инструкции для SuperStorage SSG-136R-NR32JBF

OCZ Z-DRIVE R2 E88 512GB PCI-EXPRESS X8 SSD Datasheet preview
Z-DRIVE R2 E88 512GB PCI-EXPRESS X8 SSD
Бренд: OCZ Страницы: 2
IBM DTTA-350320 Specifications preview
DTTA-350320
Бренд: IBM Страницы: 188
V-TAC VT-5139 Instruction Manual preview
VT-5139
Бренд: V-TAC Страницы: 28
SimpleTech Zeus IOPS Product Manual preview
Zeus IOPS
Бренд: SimpleTech Страницы: 84
Soyntec HDD Box 250 User Manual preview
HDD Box 250
Бренд: Soyntec Страницы: 8
Lifetime 60209 Assembly Instructions Manual preview
60209
Бренд: Lifetime Страницы: 52
Seagate Enterprise Capacity 3.5 HDD Product Manual preview
Enterprise Capacity 3.5 HDD
Бренд: Seagate Страницы: 54
Cavalry CAXA Series User Manual preview
CAXA Series
Бренд: Cavalry Страницы: 16
Cavalry CACE Series User Manual preview
CACE Series
Бренд: Cavalry Страницы: 16
Cavalry CADA-C32A Series User Manual preview
CADA-C32A Series
Бренд: Cavalry Страницы: 18
Clarke CWC114 Assembly Instructions Manual preview
CWC114
Бренд: Clarke Страницы: 8
Sun Microsystems 711 User Manual preview
711
Бренд: Sun Microsystems Страницы: 40
Pollard 131 Assembly Instructions preview
131
Бренд: Pollard Страницы: 3
Verbatim Store n Go series Quick Install Manual preview
Store n Go series
Бренд: Verbatim Страницы: 2
Karibu 61949 Building Instructions preview
61949
Бренд: Karibu Страницы: 4
Teac HD3U-120 Installation Manual preview
HD3U-120
Бренд: Teac Страницы: 20
GAVI Folding Workbench Installation Instructions preview
Folding Workbench
Бренд: GAVI Страницы: 4
LaCie Rugged USB-C series User Manual preview
Rugged USB-C series
Бренд: LaCie Страницы: 19

Бренды по названию

Популярные бренды

Загрузить еще бренды