Supermicro SuperServer 2028BT-HTR+ Скачать руководство пользователя страница 22

Страница: 22 / 128

SuperServer

2028BT-Hxxx User Manual

3-4

3-4 Drive Carrier LEDs

The chassis includes externally accessible SAS/SATA/NVMe drives. Each drive
carrier displays two LED indicators: an activity indicator and a status indicator. The

status indicator functions in RAID configurations. For non-RAID configurations, it

remains off. See the table below for details.

LED Color

Blinking Pattern Behavior for Device

Activity LED

Blue

Blinking

I/O activity

Blue

Solid On

Idle SAS/NVMe drive installed

Off

Idle or SATA drive

Status LED

Red

Solid On

Failure of drive with RSTe

support

Red

Blinking at 1 Hz

Rebuild drive with RSTe support

Red

Blinking with two

blinks and one stop

at 1 Hz

Hot spare for drive with RSTe

support

Red

On for five

seconds, then off

Power on for drive with RSTe

support

Red

Blinking at 4 Hz

Identify drive with RSTe support

Green

Solid On

Safe to remove NVMe device

Amber

Blinking at 1 Hz

Attention state—do not remove

NVMe device

3-5 Power Supply LEDs

On the rear of the power supply module, an LED displays the status.

•

Solid Green

: When illuminated, indicates that the power supply is on.

•

Solid Amber

: When illuminated, indicates the power supply is plugged in and

turned off, or the system is off but in an abnormal state.

Содержание SuperServer 2028BT-HTR+

































































































































Результаты поиска

Содержание SuperServer 2028BT-HTR+

Отзывы:

Похожие инструкции для SuperServer 2028BT-HTR+

Бренды по названию

Популярные бренды

Supermicro SuperServer 2028BT-HTR+, Руководство пользователя

Результаты поиска

Содержание SuperServer 2028BT-HTR+

Отзывы:

Похожие инструкции для SuperServer 2028BT-HTR+

Бренды по названию

Популярные бренды