background image

PB

USER’S MANUAL 

Revision 1.0

SuperServer

®

5019P-WT

5019P-WTR

The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes 
no responsibility for any inaccuracies that may be contained in this document, and makes no commitment to update 
or to keep current the information in this manual, or to notify any person or organization of the updates. 

Please Note: 

For the most up-to-date version of this manual, please see our website at 

www.supermicro.com

.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product described in this manual 
at any time and without notice. This product, including software and documentation, is the property of Supermicro and/
or its licensors, and is supplied only under a license. Any use or reproduction of this product is not allowed, except 
as expressly permitted by the terms of said license.

IN NO EVENT WILL Super Micro Computer, Inc. BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL, 
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE THIS PRODUCT 
OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, SUPER 
MICRO COMPUTER, INC. SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED 
OR USED WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING, 
INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa Clara County in the 
State of California, USA. The State of California, County of Santa Clara shall be the exclusive venue for the resolution 
of any such disputes. Supermicro's total liability for all claims will not exceed the price paid for the hardware product. 

FCC Statement: This equipment has been tested and found to comply with the limits for a Class A digital device 
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful 
interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can 
radiate radio frequency energy and, if not installed and used in accordance with the manufacturer’s instruction manual, 
may cause harmful interference with radio communications. Operation of this equipment in a residential area is likely 
to cause harmful interference, in which case you will be required to correct the interference at your own expense.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warning applies only 
to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate Material-special handling may apply. 
See 

www.dtsc.ca.gov/hazardouswaste/perchlorate

”.

WARNING: Handling of lead solder materials used in this product may expose you to lead, a 

chemical known to the State of California to cause birth defects and other reproductive harm.

The products sold by Supermicro are not intended for and will not be used in life support systems, medical equipment, 
nuclear facilities or systems, aircraft, aircraft devices, aircraft/emergency communication devices or other critical 

systems whose failure to perform be reasonably expected to result in significant injury or loss of life or catastrophic 

property damage. Accordingly, Supermicro disclaims any and all liability, and should buyer use or sell such products 
for use in such ultra-hazardous applications, it does so entirely at its own risk. Furthermore, buyer agrees to fully 
indemnify, defend and hold Supermicro harmless for and against any and all claims, demands, actions, litigation, and 
proceedings of any kind arising out of or related to such ultra-hazardous use or sale.

Manual Revision 1.0

Release Date: August 02, 2017

Unless you request and receive written permission from Super Micro Computer, Inc., you may not copy any part of this 

document. Information in this document is subject to change without notice. Other products and companies referred 

to herein are trademarks or registered trademarks of their respective companies or mark holders.

Copyright © 2017 by Super Micro Computer, Inc. 
All rights reserved. 

Printed in the United States of America

Содержание SuperServer 1019P-WTR










































































Отзывы: