Supermicro SuperBlade SBI-620P-1C3N Скачать руководство пользователя страница 28

Страница: 28 / 104

Chapter 2: Installation and Setup

2.5 Memory

Memory Support

This motherboard supports:

•

Up to 8TB 3DS LRDIMM/LRDIMM/3DS RDIMM/RDIMM/NV-DIMM DDR4 (288-pin) ECC
memory with speeds of 3200/2933/2666 MHz in 32 memory slots

•

Up to 12TB Intel Optane PMem 200 Series memory* (512GB x16 + 256GB x16)

*Note:

Intel Optane PMem 200 Series memory is supported by the 3rd Gen Intel Xeon

Scalable (83xx/63xx/53xx/4314 Series) Processors

only. Memory speed support and Intel

PMem memory size support depend on the processors used in the system.

For validated memory, use our

Product Resources page

DDR4 Memory Support for

the 3rd Gen Intel Xeon Scalable

Processors

Type

Ranks

Per DIMM

and Data

Width

DIMM Capacity (GB)

Speed (MT/s)

One DIMM

per Channel

Two DIMMs

per Channel

4 Gb

8 Gb

1.2 Volts

RDIMM

SRx8

8GB

16GB

3200*

SRx4

16GB

32GB

DRx8

16GB

32GB

DRx4

32GB

64GB

RDIMM 3Ds

(4R/8R) x4 2H- 64GB

4H-128GB

2H-128GB

4H-256GB

LRDIMM

QRx4

64GB

128GB

LRDIMM 3Ds (4R/8R) X4 4H-128 GB 2H- 128 GB

4H-256 GB

*Only the 83xx and 63xx series support 3200MT/s; for other processors, memory speed as supported by the CPU.

Check the Supermicro website for possible updates to memory support.

Содержание SuperBlade SBI-620P-1C3N









































































































Результаты поиска

Содержание SuperBlade SBI-620P-1C3N

Отзывы:

Похожие инструкции для SuperBlade SBI-620P-1C3N

Бренды по названию

Популярные бренды

Supermicro SuperBlade SBI-620P-1C3N, Руководство пользователя

Результаты поиска

Содержание SuperBlade SBI-620P-1C3N

Отзывы:

Похожие инструкции для SuperBlade SBI-620P-1C3N

Бренды по названию

Популярные бренды