Supermicro 6048R-E1CR24L Скачать руководство пользователя страница 80 | Manualshive

Страница: 80 / 142

background image

6-4

S

UPER

S

TORAGE

S

YSTEM 6048R-E1CR24L User's Manual

6-4 System Fans

Three 8-cm hot-swap chassis fans and two 8-cm exhaust fans provide the cooling
for the SuperServer 6048R-E1CR24L. It is very important that the chassis top cover
is properly installed and making a good seal in order for the cooling air to circulate
properly through the chassis and cool the components. See Figure 6-3.

System Fan Failure

Fan speed is controlled by system temperature via IPMI. If a fan fails, the remaining
fans will ramp up to full speed and the overheat/fan fail LED on the control panel will
turn on. Replace any failed fan at your earliest convenience with the same type and
model (the system can continue to run with a failed fan). Remove the top chassis
cover while the system is still running to determine which of the fans has failed.

Replacing System Fans

Removing a Fan

1. Remove the top chassis cover while the system is still running to determine

which of the fans has failed.

2. Depress the tab on the side of the fan to unlock and remove the fan along

with its housing. The fan's power connections will automatically detach.

3. System power does not need to be shut down since the fans are hot-plugga-

ble.

4. Replace the failed fan with an identical 8-cm, 12 volt fan (available from

Supermicro).

5. Position the new fan into the space vacated by the failed fan previously re-

moved. A "click" can be heard when the fan is fully installed in place and the
power connections are made.

6. If the system power is on, the hot-plug feature will cause the fan to start im-

mediately upon being connected to its header on the serverboard.

Rear Exhaust Fans

The two rear exhaust fans are also hot-swappable. To remove, depress the tab on
the side of the fan to unlock it, then pull it staight up and out of the chassis.

«
...
78
79
80
81
82
...
»

Содержание 6048R-E1CR24L















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 6048R-E1CR24L

Бренд: IBM Страницы: 8

Бренд: WiebeTech Страницы: 4

Home Garden Pub

Бренд: Fishers Woodscraft Страницы: 8

Бренд: Husky Страницы: 20

Бренд: extraspace Страницы: 16

Feronia 00108066

Бренд: Hama Страницы: 8

Expansion STEB6000403

Бренд: Seagate Страницы: 5

Бренд: Johnson Controls Страницы: 2

Бренд: morse Страницы: 11

Post-Type Wall Mount Shelving

Бренд: Omega Страницы: 4

PREMIUM STP7736

Бренд: Supatool Страницы: 3

SPINPOINT MP4 HM250HJ

Бренд: Samsung Страницы: 1

Бренд: Samsung Страницы: 16

SpintPoint M8-DVR

Бренд: Samsung Страницы: 83

SPINPOINT V40 Series

Бренд: Samsung Страницы: 115

Бренд: Seagate Страницы: 86

Бренд: TyeDee Bin Страницы: 2

Бренд: STILLA Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды