Supermicro 6048R-E1CR24L Скачать руководство пользователя

Страница: 79 / 142

Chapter 6: Advanced Chassis Setup

6-3

6-3 Removing the Chassis Cover

Figure 6-2. Removing the Chassis Cover

Release Tab

Remove this screw

(if necessary)

Removing the Chassis Cover

You may need to gain access to the inside of the server to perform various main-
tenance tasks.

1. Press the release tabs to remove the cover from the locked position. Press

both tabs at the same time.

2. Once the top cover is released from the locked position, slide the cover

toward the rear of the chassis.

3. Lift the cover off the chassis.

Warning:

Except for short periods of time, do NOT operate the server without the

cover in place. The chassis cover must be in place to allow proper airflow and prevent

overheating.

Содержание 6048R-E1CR24L















































































































































Результаты поиска

Содержание 6048R-E1CR24L

Отзывы:

Похожие инструкции для 6048R-E1CR24L

Бренды по названию

Популярные бренды

Supermicro 6048R-E1CR24L, Руководство пользователя

Результаты поиска

Содержание 6048R-E1CR24L

Отзывы:

Похожие инструкции для 6048R-E1CR24L

Бренды по названию

Популярные бренды