Supermicro 6048R-E1CR24L Скачать руководство пользователя

Страница: 116 / 142

7-28

UPER

TORAGE

YSTEM 6048R-E1CR24L User's Manual

sSATA Port 0~ Port 3

Select Enabled to enable an sSATA port specified by the user. The options are

Disabled and Enabled.

Spin Up Device

On an edge detect from 0 to 1, set this item to allow the PCH to start a COMRE-
SET initialization to the device. The options are Enabled and

Disabled

Device Type

Use this item to specify if the sSATA port specified by the user should be con

nected to a Solid State drive or a Hard Disk Drive. The options are

Hard Disk

Drive

and Solid State Drive.



Server ME (Management Engine) Configuration

This feature displays the following system ME configuration settings.

•

General ME Configuration

•

Operational Firmware Version

•

Recovery Firmware Version

•

ME Firmware Features

•

ME Firmware Status #1

•

ME Firmware Status #2

•

Current State

•

Error Code

Altitude

This item indicates the altitude of this machine that is above the sea level. The
value is shown in meters. If the value is unknown, enter the number "

80000000

MCTP (Management Component Transport Protocol) Bus Owner

This item indicates the location of the MCTP Bus owner. Enter

's to all fields to

disable the MCTP Bus owner.

Содержание 6048R-E1CR24L















































































































































Результаты поиска

Содержание 6048R-E1CR24L

Отзывы:

Похожие инструкции для 6048R-E1CR24L

Бренды по названию

Популярные бренды

Supermicro 6048R-E1CR24L, Руководство пользователя

Результаты поиска

Содержание 6048R-E1CR24L

Отзывы:

Похожие инструкции для 6048R-E1CR24L

Бренды по названию

Популярные бренды