Supermicro 6048R-E1CR24L Скачать руководство пользователя

Страница: 27 / 142

Chapter 3: System Interface

3-3

NIC2

Indicates network activity on the LAN2 port when flashing.

HDD

Indicates IDE channel activity. On the SuperServer 6048R-E1CR24L, this LED

indicates hard and/or DVD-ROM drive activity when flashing.

Power

Indicates power is being supplied to the system's power supply units. This LED
should normally be illuminated when the system is operating.

3-4 Drive Carrier LEDs

The chassis includes externally accessible SAS/SATA drives. Each drive carrier
displays two status LEDs on the front of the carrier.

LED Color

State

Status

Activity LED

Blue

Solid On

SAS/SATA drive installed

Blue

Blinking

I/O activity

Status LED

Red

Solid On

Failed drive for SAS/SATA with

RSTe support

Red

Blinking at 1 Hz

Rebuild drive for SAS/SATA with

RSTe support

Red

Blinking with two

blinks and one stop

at 1 Hz

Hot spare for SAS/SATA with

RSTe support

Red

On for five

seconds, then off

Power on for SAS/SATA with

RSTe support

Red

Blinking at 4 Hz

Identify drive for SAS/SATA with

RSTe support

Содержание 6048R-E1CR24L















































































































































Результаты поиска

Содержание 6048R-E1CR24L

Отзывы:

Похожие инструкции для 6048R-E1CR24L

Бренды по названию

Популярные бренды

Supermicro 6048R-E1CR24L, Руководство пользователя

Результаты поиска

Содержание 6048R-E1CR24L

Отзывы:

Похожие инструкции для 6048R-E1CR24L

Бренды по названию

Популярные бренды