Supermicro 6048R-E1CR24L Скачать руководство пользователя | Manualshive

Страница: 82 / 142

background image

6-6

S

UPER

S

TORAGE

S

YSTEM 6048R-E1CR24L User's Manual

SATA Drive Installation

Mounting a SATA Drive in a Drive Carrier

The SATA drives are mounted in drive carriers to simplify their installation and

removal from the chassis. These carriers also help promote proper airflow for the

drives. For this reason, even empty carriers without SATA drives installed must re-
main in the chassis. To add a new SATA drive, install a drive into the carrier with the
printed circuit board side facing down so that the mounting holes align with those in
the carrier. Secure the drive to the carrier with four screws, as shown in Figure 6-3.

Installing/Removing SATA Drives

1.

To remove a SATA drive carrier, first push the release button located beside

the drive's LEDs.

2. Swing the handle fully out and use it to pull the drive carrier straight out.

Installing a Hard Drive to the Hard Drive Tray

1. Remove the two screws securing the dummy drive to the drive tray and

remove the dummy drive.Place the hard drive tray on a flat surface such as a

desk, table or work bench (see Figure 6-4).

2. Slide the hard drive into the tray with the printed circuit board side facing

down.

3. Carefully align the mounting holes in both the drive tray and the hard drive.

4. Secure the hard drive to the tray using six screws.

5. Replace the drive tray into the chassis. Make sure to close the drive tray

handle to lock the drive tray into place (see Figure 6-5)..

Warning:

Enterprise level hard disk drives are recommended for use in Supermicro

chassis and servers. For information on recommended HDDs, visit the Supermicro
website at http://www.supermicro.com/products/nfo/files/storage/SAS-1-Com-
pList-110909.pdf

«
...
80
81
82
83
84
...
»

Содержание 6048R-E1CR24L















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 6048R-E1CR24L

StorNext QM1200

Бренд: Quantum Страницы: 9

Бренд: Overland Storage Страницы: 6

Бренд: Velleman Страницы: 4

Бренд: QPS Страницы: 9

VPFEM4128GSCBMTL

Бренд: Viking Technology Страницы: 36

My Book World Edition WDH1NC10000

Бренд: Western Digital Страницы: 2

STORAGE CAB4000 -

Бренд: Tandberg Data Страницы: 13

Бренд: Netstor Страницы: 11

Бренд: Yardmaster Страницы: 24

Бренд: Actidata Страницы: 8

CHEETAH NS 10K.2 ST3450802SS

Бренд: Seagate Страницы: 80

Бренд: Panasonic Страницы: 4

Бренд: Panasonic Страницы: 8

SUPERDISK LKM-FK73-D

Бренд: Panasonic Страницы: 17

Бренд: Panasonic Страницы: 14

Бренд: Panasonic Страницы: 26

Бренд: Panasonic Страницы: 34

Бренд: Panasonic Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды