Supermicro 5018D2-AR12L Скачать руководство пользователя страница 95

Страница: 95 / 124

Chapter 7: BIOS

7-17

*If the item "Configure SATA as" is set to IDE, the following items will

display:

SATA Frozen

Use this item to enable the HDD Security Frozen Mode. The options are

Dis-

abled

and Enabled.

Port 0 ~ Port 4 SATA Device Type (Available when a SATA port is
detected)

Use this item to specify if the SATA port specified by the user should be con

nected to a Solid State drive or a Hard Disk Drive. The options are Hard Disk

Drive and Solid State Drive.



Server ME (Management Engine) Configuration

This feature displays the following system ME configuration settings.

•

General ME Configuration

•

Operational Firmware Version

•

ME Firmware Type

•

Recovery Firmware Version

•

ME Firmware Features

•

ME Firmware Status #1

•

ME Firmware Status #2

•

Current State

•

Error Code



PCIe/PCI/PnP Configuration

The following information will display:

•

PCI Bus Driver Version

•

PCI Devices Common Settings:

PCI PERR/SERR Support

Содержание 5018D2-AR12L





























































































































Результаты поиска

Содержание 5018D2-AR12L

Отзывы:

Похожие инструкции для 5018D2-AR12L

Бренды по названию

Популярные бренды

Supermicro 5018D2-AR12L, Руководство пользователя

Результаты поиска

Содержание 5018D2-AR12L

Отзывы:

Похожие инструкции для 5018D2-AR12L

Бренды по названию

Популярные бренды