Supermicro 5018D2-AR12L Скачать руководство пользователя страница 64

Страница: 64 / 124

5-18

UPER

TORAGE

YSTEM 5018D2-AR12L/D4-AR12L/D8-AR12L User's Manual

BIOS Recovery

Close pins 2 and 3 of jumper JBR1 for

BIOS recovery. The default setting is on

pins 1 and 2 for normal operation. See

the table on the right for jumper settings.

BIOS Recovery

Jumper Settings

Pin# Definition

Pins 1-2

Normal

Pins 2-3

BIOS Recovery

BMC Enabled

JPB1 allows you to enable the BMC

(Baseboard Management Control) chip

and the onboard IPMI connection for

debugging purpose only. After the BMC

is disabled, IPMI health and remote

management functions are no longer

supported. See the table on the right for

jumper settings.

Note:

Please aways keep BMC enabled

to make sure that the platform operates

reliably with the health monitor.

BMC Enabled

Jumper Settings

Pin# Definition

Pins 1-2

Enabled (Default)

Pins 2-3

Disabled

10GbE LAN Ports Enable/Disable

JPTG1 is used to enable or disable

10GbE support. See the table on the

right for jumper settings.

10Gb Enable/Disable

Jumper Settings

Pin# Definition

Pins 1-2

Enabled (Default)

Pins 2-3

Disabled

GbE LAN Ports Enable/Disable

Jumpers JPL1 and JPL2 are used to

enable or disable LAN ports 1 and 2,

respectively. Use JPL3 to enable or

disable LAN ports 3, 4, 5, and 6. See

the table on the right for jumper settings.

GbE LAN Enable

Jumper Settings

Pin# Definition

Pins 1-2

Enabled (Default)

Pins 2-3

Disabled

SAS Port Enable/Disable

Use JPS1 to enable the onboard SAS

ports. See the table on the right for

jumper settings.

SAS Port Enable/Disable

Jumper Settings

Pin# Definition

Pins 1-2

Enabled (Default)

Pins 2-3

Disabled

Содержание 5018D2-AR12L





























































































































Результаты поиска

Содержание 5018D2-AR12L

Отзывы:

Похожие инструкции для 5018D2-AR12L

Бренды по названию

Популярные бренды

Supermicro 5018D2-AR12L, Руководство пользователя

Результаты поиска

Содержание 5018D2-AR12L

Отзывы:

Похожие инструкции для 5018D2-AR12L

Бренды по названию

Популярные бренды